Home

Egg Directory / Search

New Eggs / Best of New
New Blogs / Pics / Activity
New Files / Movies
Community Forum

Group Directory

 

 
THE EGG DIRECTORY
Pranks / Black Sheep / Rants
Edit PageMessage shenron200Add CommentAdd to FavoritesEmail to Friend

how to make a 22 lr revolver out of a metal cap gun?
DO NOT TRY THIS AT HOME : Rotteneggs.com text files and message bases are for INFORMATIONAL PURPOSES ONLY. DO NOT undertake any project based upon any information obtained from this or any other web site.We are not responsible for, nor do we assume any liability for, damages resulting from the use of any information on this site.
(36 votes)
Published: Nov 06, 2004 12:00 a.m.
In 2 Favorites Lists
Viewed 6977 times

Iknow most of you will think im crazy for making this but so what.

22lr revolver


Items needed
::::::::::::

1. a cap gun that is all metal and must work on cap ring.Also all mechanisms in the gun must be metal.Metal cap guns are hard to find but if your lucky, you’ll have a new gun.

2. Drill and drill bits the size of the desired bulletand the size of the pen tube that fits the bullet ,remember the rim of the casing should not be able to go through the hole drilled.

3. electric tape

4. steel pen tube that can fit the bullet inside of it and should be small enough to fit in the hole drilled for the barrel.
5. superglue
Construction
::::::::::::

slide out the revolving chamber and ready the drill bit the size of the bullet. if you look at the tiny holes already in the chamber where you insert the ring of caps they have a small metal bump in them . Place the drill bit on the bump and start to drill down until the bit comes throught the other side of the chamber. turn the chamber and do this to only four of the holes,try to keep them spaced apart on in each corner,becasue there are usually ten little cap holes. make sure the holes arent to close to the edge of the chamber. After drilling the four holes you will get out your pen tube that can fit the 22 bullet. switch to the drill bit the size of the pen tube and drill from the front of the barrel until it comes out in the gap left by the chamber.. make sure the chamber is out while your doing this. also make sure the tube is even with the holes in the chamber. now put super glue all on the tube and insert it into the hole in the barrel you just made. let it dry . now wrap electric tape around the handle . open up the chamber and insert 4 22lr rimfire bullets in each hole you drilled. close the chamber. You can shoot four 22 shells in semi automatic . it is acurate up to 15 yards. the hammer that uaually slam the caps into the pieces of metal is now your striking pin that hits the primer on the back of the bullet which makes it fire. your mechanism that makes the chamber revolve should still be intack so the chamber will spin to the new shots. It lets off a relatively low kick. 		 
Add Egg To Watchlist

 


Louie-1333
Nov 17, 2008 3:16 am -
You copied this


J-Dog-9383
Sep 29, 2007 11:01 pm -
rhis dude copied u
http://www.rotteneggs.c m/r3/show/se/204449.html


wh
Jan 09, 2007 5:05 am -
THIS DOESNT WORK the hammer doesnt have enuff pressure even if u rap rubber bands around it its still not enuff ive done a similar one to this but its only a single shot


BetterthantheAlternat ve
Jan 08, 2007 9:43 pm -
if you find a drill bit the right size you could drill throuh the barrel, or just cut it off and use a tiny metal pipe


Vincent-6057
May 29, 2006 7:01 pm - what gun should i use
obviosly i need a hollow barrel with now cap on the end. I accually do have a metal cap-gun revolver, however, it doesn’t have a hollow barrel. Otherwise, everything else is fine. Do you have any suggestions of if i should get a different gun (which one?), or how to make it hollow?


pyro-7611
Feb 06, 2006 4:43 pm -
Does the "firing pin" actually strike the rimfire shot? I could see this working on a centrefire but if it was aligned properly I guess it would work.


Jack-5846
Feb 17, 2005 12:44 am -
have you ever considered padding the cilender and lengthing the barrel to add a scilencer

sorry abotu my horiable spelling dislexia and sleep depreavation dont mix well
Home | Contact Us | Sign Up
Visit our companion site, Prankpedia.com
Please read the LEGAL DISCLAIMER & CONTENT GUIDELINES
© 2010 rotteneggs.com - A Social Network for Pranksters.
1.160218 (Server 1)