DO NOT TRY THIS AT HOME : Rotteneggs.com text files and message bases are for INFORMATIONAL PURPOSES ONLY. DO NOT undertake any project based upon any information obtained from this or any other web site.We are not responsible for, nor do we assume any liability for, damages resulting from the use of any information on this site.
(59 votes) Published: Jun 10, 2009 10:29 a.m. Viewed 572 times
i typed this in once an nothing good really came up so here’s how to make a paint grenaded this iz based off the Atomic Ordinance design so enjoy
P.S. this is my first egg and I don’t know how to add pics
P.P.S. if any one figures out how to rig this with a trip wire you’ll be my new best freind (not really)
to do this egg you need:
-1/4" inside diameter, 3/8" outside diameter latex tubing(You can use thinner tubing for a smaller grenade.)
-7/16" plastic washers (metal washers will also work). You can also use 1/2". 7/16" is pretty tight, while 1/2" is more sensitive and likely to go off. 7/16" is preferred.
-Cotter pins...these only need to be a little longer than the diameter of the washer
-Zip ties...used to seal the bottom of the grenade and to make a "ring" for the pull pin
-60cc 1/4" tip irrigation syringe...for filling the grenades. You may need to get this from a healthcare website; it has been brought to my attention that Wal-Mart sells a device similar to these syringes. It’s called the "MIXMIZER" and it’s used for mixing oil with gasoline so I guess you’d either look for it in Lawncare or Automotive.
-Small wood clamps...I recommend the kind that you squeeze with one hand and clamps into place.
-Children’s washable paint, diluted to desired thickness. If you can, get washable tempera paint from a craft store. The best "fill" I have come up with is one part washable tempera paint diluted with one-half to one part tap water. It’s very thick.
The first step is to cut a length of tubing. You can use any length you want, we liked a total length of about (edit:) 4-5 inches best for shape. After your tube is cut, fold the last 1/2" over itself and zip tie it together as hard as you can.
Next ready a syringe by drawing about 2 oz. of paint up. secure the tube as far up the nozzle as it will go. Make sure you are pinching the hose around the nozzle so it won’t leak. Make sure the push part of the syringe is braced against your chest or stomach, because once paint is in the latex tube, it will be pressurized and want to shoot the plunger right out of the syringe.
Push the paint into the grenade tube and hold it with your off hand, making sure to keep pressure on the plunger and keep pinching the end of the tube against the nozzle so nothing leaks.
With your other hand, clamp the grenade tube at the syringe nozzle.
Ready another syringe of paint and plug it snug into the tube. MAKE SURE AT THIS POINT YOU BRACE THE PLUNGER AGAINST SOMETHING SOLID. You wouldn’t want pink, minty paint all over yourself, now would you?
Release the clamp and push the extra paint into the grenade. Repeat the clamping procedure and fill the grenade to the desired size (we did 6 ouncers).
Once you get the grenade to the right size, clamp it one last time and grab a washer. Fold the end of the grenade over itself the same way as if you were going to zip tie it. Wedge the washer over the folded end of the tube.(For the AO design you would put a rubber band over the fold and triple it over itself, instead of the washer)
Push a cotter pin through the fold of the tube (do not actually puncture it) and over the washer. Make sure the tube is stretched over the cotter pin, which should be pushing against the washer.
Now you can release the clamp and the grenade should not leak or go off. Pull the tube through the washer and pin like a belt buckle to tighten it up and get a little extra tube past the pin so it doesn’t slide out.
You now have a paint grenade! You will need to play with how tight you make the washer to get it to your liking in terms of how much force is needed to set it off. With 7/16" washers, I pretty much pull them right up to the pin. This makes the grenade rather sensitive, so much that you must be somewhat gentle when removing the pin. When they hit something, the washer is blown off and the grenade starts a-spinnin’! i tested ours (with water) from halfway up the stairs, chucking them into the bathroom. Every surface was hit with the grenade, even the ceiling.
Jun 10, 2009 5:12 pm - Pictures. Upload all your pictures at imageshack.us and put the links between [.img].[./img.](- the periods) tags. Repost. Holdin’ my vote.
Jun 10, 2009 9:02 pm - Trip Wire I think I know a way for you to rig a trip wire. First. make sure that when you tie the end of the tube at the beginning, put a string under the zip tie and once it is sealed off, tie the string and cut it to a few feet. When you secure the washer, make sure to tie another string to the washer, to whatever distance you want the tripwire to be. Now, when you set it up, tie both strings to tent pegs (or some other solid object). Make sure that the string is not tight, but tight enough so you do not have to pull very far to trigger it. Heres the beauty of the design: the tripwire will not go off until someone pulls the pin. If you like this idea, I could always use more points and could really use a higher rating on my profile and egg.
Jun 13, 2009 7:32 pm - my freind emailed this afew days ago so i decided to turn this into an egg but idk might of got it from this wikihow place an ive never heard of it so sorry
highest regards, OFFEI
Edit Page
Message OFFEI
Add Comment
Add to Favorites
Email to Friend
