DO NOT TRY THIS AT HOME : Rotteneggs.com text files and message bases are for INFORMATIONAL PURPOSES ONLY. DO NOT undertake any project based upon any information obtained from this or any other web site.We are not responsible for, nor do we assume any liability for, damages resulting from the use of any information on this site.
(197 votes) Published: May 02, 2007 11:01 p.m. In 2 Favorites Lists Viewed 1364 times
Hi,
in this egg ill show you how to make a tube (out of a bic Cristal M pen) that holds in water when the other end isn’t even sealed.
Materials:
Scissors (Buy some)
Bic Cristal M Pen (May work with other ballpoint pens)
A lighter (Buy one)
Concrete (Outside)
Water/Liquid (Tap)
Step 1:
Get your lighter and pen
Step 2:
Take the ink out of your pen and chuck it away or use it as a dart :)
Step 3:
Burn the side that you would write with
Step 4:
The burnt part should still be hot, start squishing it on the concrete until its a big chunk
Step 5:
Get your scissors and cut off that chunk
Step 6:
Get your lighter and lightly burn the sides and then slowy plow it on the concrete
Step 7:
Now that side is finished, it should have a hole in it and look like this
Step 8:
Turn around the pen and get the side with the cap in it (Dont take the cap out, it doesnt need a hole mine had a hole from something before)
Step 9:
Get your lighter and lightly burn that side too
Step 10:
Once again slowly plow it on the concrete
Step 11:
Thats your end product it should look like this
Step 12:
Get your liquid, I used cordial because if i used water it wouldnt be visible in the pictures so i used cordial because its red (Extra Juicy 90% Fruit Juice Cordial!!)
Step 13:
Hold it up and let some of the water drain out (it drains out by itself somehow..)
Step 14:
Get a cloth and wipe it (wipe the sides so you dont get your hands sticky :D )
Step 15:
Turn it upside down and magically the liquid stays inside
Step 16:
Ta-da!
Step 17:
The one on the left is the first one i made and it suprisingly stayed in and then i decided to make an egg, the one on the right is what i made in the egg :)
Now heres that video i promised earlier in the title:
Im not sure what you can use this for, you could use it for a magic trick or something? a test tube like i would?, its your choice :)
How i found it out:
I was just melting pens and decided to make some kind of test tube, i put in water and surprisingly it stays.
How it works:
I have absolutely no idea :)
I think it uses suction or something.
This egg was 100% thought of by me, do not say C/P, if you think it is a copy paste provide me with a link!
if you down rate please give reason.
May 03, 2007 3:47 am - stash?? could be used as a stash or temp to trans chemicals or other liquids for later purposes. IE; acids or caustics that would eat through almost anything but plastics.
May 03, 2007 7:13 am - it works because the weight of the liguid creates pressure below itself which is confined in the remainder of the tube, and the rest is just newtons 3rd. It can be used as a super accurate measuring device, asuming you go thru the time to calibrate and mark it
May 03, 2007 9:27 am - ghey, i used do this too but i would make pipes not little candy holders! maybe if there was some lsd inside it might be cool.
3*
May 03, 2007 3:47 am - stash??
could be used as a stash or temp to trans chemicals or other liquids for later purposes. IE; acids or caustics that would eat through almost anything but plastics.
no dont do that cause it will come out if u shake it
Quote:
How it works:
I have absolutely no idea :)
I think it uses suction or something.
work by different air pressure 4* just cause it is well writen but the info is shit
I like it, 5*
you can get the same effect by putting a straw in a cup full of water and putting your finger over the other end, the water stays in the straw till you take your finger off, its kinda cool lol, good way to wet people without getting them really pissed off
Edit Page
Message Phil
Add Comment
Add to Favorites
Email to Friend
