DO NOT TRY THIS AT HOME : Rotteneggs.com text files and message bases are for INFORMATIONAL PURPOSES ONLY. DO NOT undertake any project based upon any information obtained from this or any other web site.We are not responsible for, nor do we assume any liability for, damages resulting from the use of any information on this site.
(29 votes) Published: Jun 23, 2003 12:00 a.m. Viewed 8144 times
If you like smoking weed out of a pipe but dont feel like spending $25 and up on getting a pipe, heres a real easy way to make a cheap,efficient pipe.
MATERIALS:
1.Tin foil (preferably the heavy duty kind but it doesnt really matter)
2. Something to use to wrap the tin foil around when making the bowl and the stem (a big pencil and the inside part of a bic pen work fine)
3. Something to make holes with (a sharp knife will work fine as long as your careful and dont cut yourself)
4. Glue (a glue gun works fine)
STEPS:
1. Take whatever your using to shape the inside of the stem and break off a piece of tin foil.
Note: The amount of tin foil you pull is going to be the length of your stem.
EX. If you pull the tin foil out 5 inches, your stem will be around 5 inches.
2. Wrap the tin foil around the object your using. Make sure that you get it as tight as you can without ripping the tin foil. To make the pipe sturdier, add more tin foil of about the same length.
Note: LEAVE A SMALL PART OF TIN FOIL THAT IS FAIRLY THIN ON THE END. YOU NEED THIS WHEN CONNECTING THE STEM TO THE BOWL!
3. Take the object that you are going to be using to help shape your bowl. The thicker the object, the bigger the inside of the bowl will be and visa versa. Take a piece of tin foil and shape it around the object. Keep doing this until you have a fairly good foundation.
4. Make sure you push the top part of the bowl down a little so no parts of tin foil are sticking out.
5. Cut some squares of tin foil out (the size depends on how big the bowl is). You will be using these for a screen, so the more you have the thicker the screen. Push the tin foil in to the bowl so they are deep enough to put your weed into the bowl, but not too deep that you cant put the stem below it. I like to put my screen a little past half way down. Push the outer edges of the screen against the outer part of the bowl.
6. Cover the bowl again with some more tin foil to cover the edges of the screen and to make it sturdier. Add as much as you would like again (the more you add, the sturdier it will be).
7. This step is optional, but I strongly suggest you do it. Cover the whole bowl with a sheet of tin foil. Then find where the bowl is and cut a hole and push the small parts of the tin foil that hang over the bowl inside of it. By doing this step, it makes the bowl look nicer and it makes sure there is no loose things that could come undone.
8. Using your "drill-like" tool, put a small hole in the middle of your screen. It needs to be small enough that things cant get through there, but big enough that you can draw air through it. Next, drill a hole near the bottom of the pipe so you can put the stem in there. This is why you left a thin layer at the end of the pipe (so it will fit into the bowl). Make sure you dont drill the whole too big that air can escape and not too small that it will close the stems hole and you wont be able to draw any smoke.
9. Once you’ve placed the stem into the hole in the bowl, place a sealant (glue, preferably a glue gun) where the two meet. This will keep air from escaping from any space near the hole. After that dries take a hit as if something was in there to make sure no air is escaping from anywhere else. There may be some bits of tin foil that get in your mouth when you do so, but after doing that a couple of times it wont be a problem.
10. Get some weed (or tobacco), but it in the bowl, and light that #*@! up. :)
Edit Page
Message lebpyro
Add Comment
Add to Favorites
Email to Friend