Ok This is my first egg, so yeah...

This is an egg with some home made weapons. I had alot more but i lost the crap i wrote down. Sorry if some of this is reposted.


1.) Bow and Arrow

Stuff needed:

1.) 1 flexible Ruler {the shatter resistant kind}
2.) 2 rubber bands/or one big rubber band
3.) Bamboo Skewer/something that is long and can be shot


First:

Take the ruler and Drill a hole on each end.
(*If it doesnt already have a hole in the middle drill one there too*)
____________________________________
| |
|O 0 O|
|___________________________________|


Then take the two rubber bands and snap them in half
so you have 2 long stretchy things. Then tie them to gether to make it like a rope.

After that tie one end of the rubber band on the ends of the ruler {through the holes}:::you might have to bend the ruler to get it on.
Or if you have a long rubber band just snap it and tie it on.

Then Put in the bamboo skewer and shoot stuff. Try making lighter arrows because the bamboo thing is really heavy and doesnt shoot too good.

When your not using it un-tie one end of the rubber band to release tension on the rubber bands and the ruler. After a wile the rubberbands will get to loose and you will have to replace them. the ruler will bend to much if you leave it tied up., Have fun.






I also like making crappy blowguns.

Crappy blowguns:

Materials:

1.) 4-5 Bic pens
2.) Tape

First take out the ink of the pens and then the end cap thing. [do with all pens]

Then Tape The pens together. Make sure they are lined up straight and if you bent the end of the pen while taking out the ink and stuff dont put it on the end that the dart will be leaving from. Have the end of the gun as round and unbent as posible [if u didnt know this makes the dart more accurate]

I reccomend just buying one for 10 bucks. theyre alot better.

When your done making the gun you need some goddam ammo.

Ammo/darts

Supplies:

1.) Paper
2.) Hot glue or Super Glue [super glue is ALOT better and eaiser)
3.) Needles

I use paper darts because they are pretty easy to make and go faster and are more accurate.

First Take the paper and roll it into a small cone.[small enough to fit in the pen--Duh--]have the pointed end almost completly closed, so a needle can just barley fit through.

When youre done rolling it tape it into place so it doesnt un-roll. Dont use to much paper or you wont be able to get the needle through.

Then stick the needle through the open part of the cone[the back side]and pull it untill it is sticking out all the way.

Now you get to wait for the glue gun to get hot, or if youre lucky u have super glue.

Glue it right where the needle and the cone meet[the end of the cone. If you use hot glue dont let it pile up or your dart will suck. try to make it flat and even [aka aerodynamic?][lol]
You might try covering the cone in super glue.

If you dont cover the cone in super glue after a while the paper will start to get all bendable and either rip or just plain suck.


Dart # 2

Shoe lace dart

I think this has been posted but im gonna make it my way[not to different]

1.) shoelace [not fat laces]
2.) Needles
3.) Something to cut with

Cut the end of the shoe lace off sop you have the hard plastic thing and about an inch or so of frayed shoelace. If the shoelace part didnt get all loose and spread out pull on it to make it frayed like a mother.

Then stick the needle through the frayed part of the shoelace out of the end with the hard plastic shit.

My needles where really short so if you need to go buy or steal what ever, some long sewing needles.

after you put the first needle through i like to have one sticking out of the end so i can pull the dart out of the crap it gets stuck in.

These are or can be really heavy and harder to shoot.
After a while of shooting it will get heavier because of moisture. Just let it dry out.



Dart for .50 cal blowgun or 1/2 inhe tubing.

This is like a super size of the paper dart above.

Supplies:
1.) Thick paper
2.) Bamboo skewer

First make a cone like for the paper dart posted above. Then stick the bamboo skewer through the end
and super glue.

This dart works GREAT it shoots expremly far and is fast.

You can also put an exacto blade on the end with epoxy or super glue. Try cutting the blade so it has a flat end and its not slanted for the exacto knife. Then cut off the end of the skewer so int not pointed and is flat. Cut a slit in the end of the skewer and glue on the exacto blade.


I would post more but this is all I remember.This is my first egg/eggs.
Sorry for not having pictures I dont have a camera and stuff and I dont want to screw up my egg trying to put them in.




Ze End!!!






For now.